Ceramic glass induction hob
ZKT 650 D
Installation and Operating Instructions
g
Contents
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Key Features of Your Appliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
4
5
6
Description of the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cooking zones and control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Digital Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cooking Zone Safety Cut-out. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Function and the Way the Induction Cooking Zone Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
7
8
8
9
Suitable Kitchenware for Induction Cooking Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Before using for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Initial Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Operating the hob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Touch Control sensor field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Switching on the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Switching Off the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Cooking Zone Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Heat Setting Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Activating the Power Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Switching off a cooking zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Cooking with the Automatic Heating-Up Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cooking without the Automatic Heating-Up Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Locking/Unlocking the Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Uses, tables and tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Advice on cooking with and without automatic warm up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Chart for Setting the Cooking Zones. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Chart for the Automatic Heating-Up Feature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Cleaning and care. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Advantages for Cleaning and Caring for the Induction Cooking Zone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Hob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
What to do if … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Rectifying faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Technical Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Regulations, Standards, Directives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Safety Instructions for the Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Guarantee Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Service and Spare Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Rating Plate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3
Operating Instructions
1 Safety
The safety aspects of this appliance comply with ac-
cepted technical standards and the German Appli-
ance Safety Law. However, as manufacturers we
also believe it is our responsibility to familiarise you
with the following safety instructions.
Special Notes on Induction Cook-
ing Zones
• Scientific studies have shown that patients who
are fitted with implanted pacemakers are not nor-
mally affected or put at risk by our induction cook-
ing zones.
The distance between the body and the cooking
zone should, however, never be less than 30 cm!
Electrical Safety
• The installation and connection of the new appli-
ance must only be carried out by qualified person-
nel.
• Repairs to the appliance are only to be carried out
by approved service engineers. Repairs carried out
by inexperienced persons may cause injury or seri-
ous malfunctioning. If your appliance needs repair-
ing, please contact your local AEG Service Force
Centre.
• Electromagnetic fields can affect electronic circuits
and interfere with portable transistor radios.
• Do not put magnetically rechargeable objects (e.g.,
credit cards, cassettes) on the ceramic glass sur-
face while one or more induction cooking zones
are in use!
• Do not put any metallic objects (e.g., spoons, pan
lids) on the induction surface as they can be
warmed up when the induction surface is in use.
3
Please follow these instructions, otherwise the
warranty will not cover any damage that may
occur.
3
Some cookware can produce noises when
used on induction cooking zones. This is not a
fault in the hob and its function will not be im-
paired in any way as a result.
• Flush-mounted appliances may only be operated
following installation in suitable installation cabi-
nets and workplaces which conform to the relevant
standards. This ensures sufficient protection
against contact for electrical units as required by
the VDE [Association of German Electrical Engi-
neers].
• If your appliance malfunctions or if fractures,
cracks or splits appear:
– switch off all cooking zones,
Safety When Cleaning
• For safety reasons do not clean the appliance with
a steam jet or high pressure cleaner.
• Clean the hob in accordance with the maintenance
and cleaning instructions in this manual.
– disconnect the hob from the electricity supply.
Child Safety
The cooking zones will become hot when you cook.
Therefore, always keep small children away from the
appliance.
Safety During Use
• This appliance may only be used for normal cook-
ing and frying in the home. It is not designed for
commercial or industrial purposes.
• Do not use the hob to heat the room.
• Take care when plugging electric appliances into
mains sockets near the hob. Connection leads
must not come into contact with the hot surface.
• Overheated fats and oils catch fire quickly. You
should supervise cooking when preparing foods in
fat or oil (e.g. chips).
• Switch off the cooking zones after use.
4
How to avoid damage to the appli-
ance
• Do not use the cooking area as a worktop or stor-
age space.
• The frameless edge of the glass ceramic surface is
susceptible to knocks. Please be careful when
moving pots and pans around.
• Do not have the cook zones on with empty pans,
or with no pots or pans on them.
• Ceramic glass is very tough, and impervious to
sharp temperature changes, but is not unbreaka-
ble. It can be damaged if particularly hard or sharp
objects fall on to it.
• Do not use pots made of cast iron, or which have
damaged bases with rough edges or burrs. Moving
these around may cause scratches.
• If sugar or a mixture containing sugar falls onto a
hot cooking zone and melts, remove immediately,
while still hot, using a kitchen scraper. If left to cool
down, it may damage the surface when removed.
• Keep objects or materials liable to melt away from
the ceramic glass surface, for example, artificial
materials, aluminium foil, or cooking wraps. If any
other materials or foodstuffs are melting on the ce-
ramic glass surface, these should also be cleaned
away immediately, using a kitchen scraper.
2 Disposal
Disposing of the packaging materi-
al
All materials used can be fully recycled.
Plastics are marked as follows:
• >PE< for polyethylene, as used for the outer wrap-
ping and the bags inside.
• >PS< for polystyrene foam, e.g., as used for the
padding materials. They are completely free of
CFCs.
Disposal of old appliances
1
Warning: Before disposing of old appliances
please make them inoperable so that they
cannot be the source of danger.
To do this, disconnect the appliance from
the mains supply and remove the mains
lead.
To protect the environment, it is important that worn
out appliances are disposed of in the correct man-
ner.
• The appliance must not be disposed of with
household rubbish.
• You can obtain information about collection dates
or public refuse disposal sites from your local
Council or Environmental Health Office.
5
The Key Features of Your Appliance
• Induction cooking zones: The appliance is fitted
with a ceramic glass hob and induction cooking
zones. Induction heats the base of the pan imme-
diately and does not heat the ceramic glass hob
first.
• Sensor fields: Your appliance is operated using
Touch-Control sensor fields.
• Cleaning: The advantage of the ceramic glass
cooking surface and the sensor fields is their ac-
cessibility for cleaning. The flat surface is easy to
clean.
• On/Off sensor field: In addition to the sensor field
“On/Off” switch, the appliance has a separate
mains switch with which the mains supply to the
appliance can be completely switched on and off
with one touch.
• Sensor field lock: With this device the operating
panel can be locked, for example as a safety pre-
caution for children.
• Control and function indicators: Digital indica-
tors or control lamp provide information about set-
tings made, functions activated, as well as any
residual heat of the corresponding cooking zone.
• Safety cut-out: A safety cut-out ensures that all
cooking zones switch off automatically after a peri-
od of time if the setting has not been changed.
• Power device: With this device the power for the
appropriate cooking rings can be temporarily in-
creased.
• Keep warm setting: 1 is the setting for keeping
foods warm.
• Residual heat indicator: An h for residual heat is
shown in the display if the cooking zone becomes
so hot that there is a risk of burning.
• Timer: All rings can be automatically switched off
using the integrated timer. When the end of the
cooking time has been reached, the cooking zone
switches off.
6
Description of the Appliance
Cooking zones and control panel
Induction cooking zone 1800 W
Induction cooking zone 1400 W
Touch-Control panel
Induction cooking zone 1800 W
with power function 2300 W
Induction cooking zone 2200 W
with power function 3000 W
Cooking zone displays
Timer operation
Lock with
control indicator
Heat setting displays
Display timer
Timer
Cooking zone
selection
Power zone
activation
Mains button
“On/Off”
Heat setting selector +
and -
7
The Digital Displays
1 Cooking Zone Safety
Digits 1 to 9 and four different letters can appear in
the display.
Cut-out
If one of the cooking zones is not switched off after a
certain time or if the heat setting is not changed, the
corresponding cooking zone switches itself off auto-
matically.
h appears in the ring display for all rings that were
switched on, and _ after they have cooled down.
• The digits show the heat setting selected.
1 = Lowest capacity
9 = Highest capacity
p = Power level
• The following letters and functions are displayed
for the cooking zones:
The rings are switched off at:
• Heat setting
• Heat setting
• Heat setting
• Heat setting
1 - 2
3 - 4
5
after 6 hours
after 5 hours
after 4 hours
after 1.5 hours
1
h = Residual Heat Display
Danger! Cooking zone still hot; it extinguishes
when the cooking zone has cooled down. This
display appears only if the cooking zone is
switched off, but the hob is still connected to
the electricity supply.
6 - 9
3
If one or more cooking zones switch off before
the times indicated see section “What to do
if …”.
a = Automatic heating-up (possible for all cook-
ing zones)
is lit, if the cooking zone is set to automatic heating-
up; (remains lit until the automatic feature switches
over to the continued heat setting selected).
Cancelling the Safety Cut-out
To cancel the activated safety cut-out the appliance
must be switched off and then on again using the
ON/OFF
are again ready for use.
sensor field. After this the cooking zones
_ = Lights up when the automatic switch-off func-
tion has been activated (also see “What to do if ...?”).
Switching Off for Other Reasons
1f = Error display
flashes if the cooking zone is activated and
– no pan is on the cooking zone or
– unsuitable pots and pans are used
Liquids that boil over onto the control panel cause all
cooking zones to switch off immediately.
If you place a wet cloth on the control panel it has
the same effect. In both cases the appliance has to
be switched on again using the mains switch after
removing the liquid or cloth.
p = Power function
lights up when the Power function is activated.
The Power function supplies extra-high heating ca-
pacity. It can be activated for the front two cooking
zones.
8
Function and the Way the
Induction Cooking Zone
Works
A copper wire induction coil is beneath the ceramic
glass cooking surface. This generates electromag-
netic fields, which act directly on the base of the
pots and pans and not, as with other heating up
methods, first heating the ceramic glass. This means
that the base of the pan is immediately heated up,
which saves time and energy.
Since the heat required for cooking is generated di-
rectly in the base of the pan the cooking zone itself
hardly warms up. It only receives the reflected heat
from the pan base.
Note:
If there is no pot or pan on the cooking zone there is
no energy transfer (heating up) and therefore gives
protection against the cooking zones being switched
on accidentally.
3
A cooling fan is an integral part of this hob and
comes on automatically depending on the
temperature of the induction cooking zone.
The cooling fan works in two speed levels de-
pending on usage. The cooling fan will contin-
ue to run for a short period after the cooking
zone has been switched off.
9
Automatic Pan Sensing
Suitable Kitchenware for
Induction Cooking Zones
The induction cooking zone does not function when
unsuitable pans are used.
If the cooking zone is switched on without a suit-
able pan on it f flashes in the digital display of
the cooking zone.
After about 10 minutes the cooking zone switches it-
self off automatically. _ appears in the digital dis-
play.
Also when overheating occurs (e.g. heating up a pan
that is empty) or with faults in the electronics the dis-
play _ is lit. The cooking zone switches itself off au-
tomatically.
To be able to use it again the cooking zone must
have been first switched off and then reset to the re-
quired heat setting.
Pots and Pans
• In principle all pots and pans with magnetic bases
are suitable. These are steel, steel-enamel as well
as cast-iron pots and pans.
• High grade steel pans with a mixed metal base
(sandwich base, e.g. Tefal with an aluminium/cop-
per base) are suitable for induction only if the man-
ufacturer has expressly marked them as such. In
that case they have a ferromagnetic percentage in
the base.
• If you wish to use a special type of pan (e.g. a pres-
sure cooker, simmering pan, wok, etc.), please ob-
serve the manufacturer's instructions.
• Aluminium, copper, brass, stainless steel pots and
pans (unless specifically designated as suitable for
induction), glass, ceramic or porcelain are not suit-
able for induction cooking zones. The cooking
zone reacts as if it were being used without a pot
or pan: Error code f.
Look for the label: Suitable for induction!
Suitability Test
If you are not sure if a pot or pan is suitable for cook-
ing or frying on the induction cooking zone you can
check this as follows:
• Place a pot filled with a little water (3-5 mm filling
height) on the cooking zone.
Switch the cooking zone to full power (switch set-
ting 9).
Caution: The pan base of suitable kitchenware
heats up within a few seconds!
• You can also check this with a magnet. If it remains
fixed to the base the pan is suitable for induction
cooking zones.
Pan Size
Up to a certain limit the induction cooking zone
adapts itself to the size of the pan base diameter.
However, the pan base diameter must be of a mini-
mum size, depending on the size of the cooking
zone.
Diameter of the cooking zone 14,5 cm:
Diameter of the pan base at least 12 cm
Diameter of the cooking zone 18 cm:
Diameter of the pan base at least 14,5 cm
Diameter of the cooking zone 21 cm:
Diameter of the pan base at least 18 cm
Note:
Please note the diameter of the pan base when
buying new pans, since the manufacturers usually
specify the top edge diameter of their pans.
10
Before using for the first time
Initial Cleaning
Wipe the ceramic glass surface with a damp cloth.
1
Important: Do not use any caustic, abrasive
cleaners! The surface could be damaged.
Operating the hob
Touch Control sensor field
To operate the Touch Control sensor field place your
finger from above flat onto the required field until the
appropriate displays come on or go out or the re-
quired function is carried out.
Switching on the Appliance
The entire appliance is switched on using the “On/
Off” sensor field.
Touch the “On/Off” sensor field for approx.
2 seconds.
The digital displays will show _ and the decimal
point will flash.
3
Once the “On/Off” sensor field has been oper-
ated to switch on the appliance, one of the
cooking zones must be selected within ap-
prox. 10 seconds using the cooking zone se-
lection buttons. Otherwise the appliance
switches off again for safety reasons.
Switching Off the Appliance
To switch off the appliance completely activate the
“On/Off” sensor field.
Touch the “On/Off” sensor field for approx. 1 sec-
ond.
3
When an individual cooking zone or the entire
hob is switched off, any residual heat is shown
with an h (for “Hot”) in the digital display for
the appropriate cooking zones.
11
Cooking Zone Selection
To select the required cooking zone touch the corre-
sponding sensor field for approx. one second.
A zero with a decimal point will light up in the appro-
priate cooking zone display window 0.
3
The decimal point indicates that settings may
only be made for this cooking zone.
Heat Setting Selection
For setting and adjusting the heat setting (1 to 9) for
the selected cooking zone.
Use sensor field
to increase the heat setting.
Lower the heat setting with sensor field
.
3
If several cooking zones are being used simul-
taneously, the required cooking zone must be
selected by touching the appropriate sensor
field before adjusting the heat setting. The
decimal point in the display shows which
cooking zone has been selected.
12
Activating the Power Function
Using the power function you can increase the pow-
er of both front cooking zones for 10 minutes.
With this function you can, for example, bring a large
quantity of water rapidly to the boil or brown meat.
To switch on the power function, the cooking zone
must be selected (decimal point in the display).
Touch the “Power-function” sensor field
.
p appears in the display. The power function is now
active.
3
The power function will be activated for a
maximum of 10 minutes. Following this the
cooking zone automatically switches to heat
setting 9.
The power function can be switched off in the follow-
ing way:
• Touching the “Power function” sensor field
• Touching the sensor field _.
.
1
As soon as the power function is activated for
one of the front cooking zones, less heating
power is given to the rear cooking zone.
If the power function for the front right cooking zone
is activated, the rear left cooking zone can attain a
maximum heat setting of “8”.
If the power function for the front left cooking zone is
activated, the rear right cooking zone can attain a
maximum heat setting of “7”.
If a higher setting than 7 or 8 is set for the rear cook-
ing zones, the display for the rear cooking zone con-
cerned will show the differing settings alternately
(e.g., 7 and 9).
As soon as the power function has ended (after a
maximum of 10 minutes), the rear cooking zones au-
tomatically revert to their previously set heat setting.
Switching off a cooking
zone
1.Select the required cooking zone with the cooking
zone sensor fields.
2.Touch sensor fields
and
simultaneously to
switch off or turn sensor field back to zero.
3
A cooking zone may only be switched off
when the decimal point is on in the cooking
zone display.
13
Cooking with the Automatic
Heating-Up Function
All four cooking zones of the cooking field can be
controlled in nine stages and have an automatic
heating-up function:
– 1, Lowest heat setting
– 9, Highest heat setting
– a, Heating-up function.
With the automatic heating-up function (a), the
cooking zone operates for a certain time at full ca-
pacity and then automatically switches back to the
heat setting selected for further cooking.
The duration of the automatic heating-up function
depends on the heat setting selected for further
cooking.
1.Select the required cooking zone with the cooking
zone sensor fields. The decimal point in the associ-
ated display field illuminates.
2.With the
or
sensor fields select heat setting
9. Stop briefly and touch the sensor field again.
a lights up in the heat setting display.
3.Next, touch the sensor field and set the required
continued heat setting 1 to 8. The heat setting se-
lected for further cooking then is displayed.
After 5 seconds, a appears in the display again in-
stead of heat setting selected for further cooking.
The heat setting is displayed again after the heating-
up time has ended.
3
If you select a higher heat setting when the au-
tomatic function is in operation, e.g. from 3 to
5, the previous heating-up time is taken into
account. If you select a lower setting, then the
automatic function is brought to an immediate
end. If you start cooking again on a cooking
zone that is still warm, the automatic heating-
up function uses the residual heat. This saves
time and energy.
14
Cooking without the Auto-
matic Heating-Up Function
1.For heating up/browning, select a high power.
2.As soon as steam forms or the fat is hot, switch
back to the required heat setting for the remainder
of the cooking time.
3.Reset to zero in order to end cooking.
2
Note:
When cooking with the induction cooking
zone you should take into account that
– the heating-up times are reduced by the direct en-
ergy transfer to the pan!
– the cooking process stops immediately after the
cooking zone is switched off (no boiling over!)
Locking/Unlocking the
Control Panel
With the exception of the “On/Off” sensor field the
control panel can be locked at any required time dur-
ing cooking in order to prevent adjusting the settings
such as when wiping over with a cloth. This
function is also suitable as a child safety feature.
1.Touch the “Lock” sensor field until the control indi-
cator comes on.
2.To release the lock touch the “Lock” sensor field
again continuously until the control indicator goes
out.
3
Child safety feature! If the hob is completely
switched off using the “On/Off” sensor field
while the lock is on, then the lock will still be
active when the hob is switched on again. To
reactivate the cooking zones, the locking func-
tion must be cancelled as described above.
15
Timer
A cooking duration can be set with the integrated
timer for all cooking zones. When the end of the
cooking duration is reached, the cooking zone
switches itself off automatically.
1.Using the cooking zone sensor field, select the re-
quired cooking zone and set the required heat set-
ting.
2.Touch the TIMER
sensor field to activate the
timer function for this cooking zone. 00 will appear
in the display.
3.Using the or sensor fields set or adjust the re-
quired period of time until the zone is to switch off
automatically (eg. 15 minutes).
After a few seconds the timer will start automatically
and will show how much time remains before it will
switch off.
In addition, the “Timer active” display for the relevant
cooking zone will light up.
At the end of the set cooking time, the cooking zone
will switch off automatically and an acoustic signal
will sound.
4.Touch the TIMER
sensor field to switch off the
signal and control indicator.
3
To set the timer more quickly, leave your finger
on the or sensor field until the required
time is reached.
If the sensor field is operated first, the time
setting will begin at 99 minutes; if the sen-
sor field is operated first, the time setting will
begin at 1 minute.
16
Displaying the remaining cooking
time
If you select a cooking zone which is in timer mode,
the cooking time still remaining appears in the timer
display window.
Using the timer to measure short
periods of time (“Minute Minder”).
1
Important! None of the cooking zones should
be set with the Timer!
1.Touch the "On/Off" sensor field for around two
seconds.
The digital display _ flashes.
2.Touch the TIMER
sensor field to activate the Ti-
mer function.
3.Using the
or
sensor fields, set the desired
length of time (for example, 20 minutes).
The Timer begins to run after a few seconds, and in-
dicates the time remaining.
When the set time has elapsed, an audible signal is
sounded.
4.Touch the TIMER
sensor field, to switch off the
signal.
Ending the timer function prema-
turely
There are two ways of switching off the timer early:
Switching off the cooking zone and timer
simultaneously
1.Select the desired cooking zone using the cooking
zone buttons.
2.Touch the
and
buttons simultaneously: The
cooking zone and timer will switch off.
Switching off the timer - leaving the
cooking zone active
1.Select the desired cooking zone using the cooking
zone buttons.
2.Touch the “Timer” button again.
3.Touch the and buttons simultaneously:
– Only the timer will switch off.
– The cooking zone will stay on.
17
Uses, tables and tips
Advice on cooking with and
without automatic warm up
The automatic warm up function is suita-
ble for:
• dishes that start off cold, are heated up at high
power and do not need to be continually watched
when cooking on the selected heat setting,
• dishes that are put in a hot frying pan.
The automatic warm up function is not
suitable for:
• goulash, beef olives and similar braised dishes that
need continual turning until browned correctly,
have liquid added and are then braised until
cooked,
• dumplings, pasta dishes with large amounts of liq-
uid,
• cooking with pressure cookers,
• very large quantities of soup/stew with more than
2 litres of liquid.
General notes:
• When cooking without the automatic warm up
function, we recommend the use of a high heat
setting to warm up the food (using the ) and then
leave the dish to finish cooking at an appropriate
lower heat setting.
• Take special note of the results when you first use
the appliance! You can then decide which heat set-
ting is the best for "your dishes" in the "quantities
you are accustomed to preparing" with "your
pans". You will then quickly appreciate the advan-
tages of the automatic function and will feel re-
laxed about using your new hob.
• You can use the 1 heat setting for keeping food
warm.
Tip when cooking with induction cooking
zones:
• In order to obtain an even cooking result, the diam-
eter of the bottom of the pan used should not be
greater than that of the cooking area indicated on
the glass ceramic.
18
Tables
Note:
The figures given in the following tables are for guid-
ance. The switch setting required for cooking de-
pends on the quality of the pots and pans and on the
type and quantity of the foodstuffs.
Chart for Setting the Cooking Zones
Heat setting
suitable for
9 or P
Heating Up
Heating up large quantities of water, cooking pasta
Deep-frying pommes frites (chips),
browning meat, e.g. goulash,
frying, e.g. potato fritters
7-9
Heavy Browning
frying pieces of loin, steaks
Frying meat, schnitzel,
cordon bleu, chops, pancakes,
rissoles, roux, mild
6-7
4-5
Mild Frying
Boil
roasting, fried sausages, liver, eggs,
deep-frying doughnuts.
Cooking larger quantities of food,
stews and soups,
steaming potatoes,
cooking meat stock or bouillon
Steaming
Steaming
Steaming vegeables or
braising meat
cooking rice pudding
3-4
2-3
Simmering rice or milk-based dishes,
steaming smaller quantities of potatoes or vegeta-
bles, heating up ready-to-serve meals.
Simmering
Melting
Fluffy omelettes, egg royale,
Sauce hollandaise, keeping dishes warm, melting
butter, chocolate, gelatine
1-2
0
Off setting
19
Chart for the Automatic Heating-Up Feature
Cooking
processes
Heat setting
A7 to A8
Example foods
Duration
Notes/tips
Heavy brown-
ing
per pan 8-
20 min.
Steaks
Turn occasionally
Schnitzel, Rissoles,
Fried eggs, Grilled
Sausages
per pan 10-
20 min.
A6 to A7
Roasting
Turn occasionally
Turn occasionally
Pancakes, thin pan- bake continuous-
A6 to A7
A3 to A5
Baking
Boil
cakes
ly
Up to 3 litres liquid plus ingredi-
ents
Soups
40-150 min.
Do not use much liquid
e.g.: max. ¼ litre water for
750 g potatoes
Potatoes,
vegetables
A3 to A5
A2 to A4
A2 to A3
Steaming
20-60 min.
20-45 min.
25-50 min.
Stewing, de-
frosting
Add a little liquid (some spoon-
fulls) if required
Vegetables
Add at least double the quantity
of liquid to the rice etc. Stir oc-
casionally
Rice, millet, buck-
wheat
Simmering
Depending on the quantity
adapt the setting
A2 to A3
1 to A2
1 to A2
Heating up
Thickening
melting
Ready meals, stews
10-30 min.
10-20 min.
5-25 min.
Fluffy omelettes, egg
royale
Chocolate/butter/
gelatine
Without bain-marie
Stir occasionally!
20
Cleaning and care
Advantages for Cleaning
and Caring for the Induc-
tion Cooking Zone
2
The cleaning effort for induction ceramic glass
cooking surfaces is considerably less than for
cooking surfaces with radiant heating:
– The induction cooking zone reacts faster to switch-
ing down and off. Boiling over and burning in of
dishes is avoided to a large degree.
– The temperaturs on the ceramic glass surface are
clearly lower with inductive cooking than with the
conventional radiant heating systems.
Since the heat is generated in the pan, food or food-
stuffs possibly on the glass ceramic surface are not
burnt in as badly.
Hob
1
Important: Cleaning agents must not come
into contact with the warm ceramic glass sur-
face! All cleaning agents must be removed
with plenty of clean water after cleaning be-
cause they can have a caustic effect when the
rings are next heated!
Do not use any aggressive cleaners such as
grill or oven sprays, coarse scourers or abra-
sive pan cleaners.
3
Clean the ceramic glass surface after each use
when it is warm to the touch or cold. This will
avoid spillages becoming burnt on.
Remove scale and water marks, fat spots
and discolouration with a metallic shimmer
using a commercially available ceramic glass
or stainless steel cleaner.
Light Soiling
1.Wipe the ceramic glass surface with a damp cloth
and a little washing up liquid.
2.Then rub dry with a clean cloth. Remnants of
cleaner must not be left on the surface.
3.Thoroughly clean the entire ceramic glass cooking
surface once a week with a commercially available
ceramic glass or stainless steel cleaner.
4.Then wipe the ceramic glass surface using plenty
of clean water and rub dry with a clean fluff-free
cloth.
21
Stubborn Soiling
1.To remove food that has boiled over or stubborn
splashes, use a glass scraper.
2.Place the glass scraper at an angle to the ceramic
glass surface.
3.Remove soiling by sliding the blade.
3
You can obtain glass scrapers and ceramic
glass cleaners from your local Service Force
Centre.
Scratches or dark marks on the ceramic glass sur-
face, caused for example by a pan base with sharp
edges, cannot be removed. However, they do not
impair the function of the hob.
22
What to do if …
… the letter _ or h is still displayed by
the residual heat indicator after switch-
ing off the cooking zones.
Check whether
– the cooking zone has only been on for a short time
and is therefore not yet hot enough.
If the cooking zone is hot, please ring customer serv-
ice.
Rectifying faults
It is possible that faults have been caused by a minor
error, which you can correct yourself with the help of
the following instructions. Do not attempt any further
repairs if the following instructions do not help in
each specific case.
1
Warning! Repairs to the appliance are only to
be carried out by approved service engineers.
Improperly effected repairs may result in con-
siderable risk to the user. If your appliance
needs repairing, please contact your specialist
dealer or local Service Force Centre.
… a cooking zone cannot be switched off
Check whether
– the sensor fields may be partially covered by a
damp cloth or by liquid.
– the lock mechanism is switched on.
If the ceramic glass hob is broken, please quote the
3-digit number on the glass hob when contacting
customer service.
… a cooking zone cannot be switched on
Check whether
– the lock mechanism is switched on.
What to do if …
… the indicator f is flashing
Check whether
– the pan is located on the correct cooking zone,
– the diameter of the pan base is too small for the
cooking zone,
… the appliance develops a fault or the
ceramic glass hob is broken or cracked.
– Switch off all cooking zones.
– Switch off the fuse for the cooking zone or take it
out.
– the pan is suitable for induction.
… _ appears on the display
Check whether
… the cooking zones are not working.
Check whether
– the cooking zone has overheated.
switch off the appropriate cooking zone and let it
cool down. Try switching on the cooking zone
again using a suitable pan after a few minutes.
– the automatic switch-down for the cooking zone
has triggered.
– the appropriate fuse in the house installation (fuse
box) is intact. If fuses are triggered more than
once, call a qualified electrician.
– the appliance is switched on properly,
– the control lights on the operating panel are illumi-
nated,
– the appropriate cooking zone is switched on,
– the cooking zones are set to the desired heat (see
chapter “Cooking”),
– the safety shut-down for the cooking zones has
triggered (see chapter “Safety devices”).
You can reactivate the cooking zone by switching it
off and on briefly.
… the power function cannot be
switched on?
– Switch off the cooking zone for approx. 10 min-
utes.
If this fault occurs repeatedly, check
– whether the requisite ventilation gap between the
work surface and the cabinet panel underneath it
has been covered over.
– that a sufficiently large ventilation gap was main-
tained under the work surface when the appliance
was installed (5 mm).
… the cooking zones will not switch on.
Check whether
– the operating panel is locked (see chapter “Lock-
ing the operating panel”).
– a period of more than 10 seconds elapses after
operating the “On/Off” switch and before the se-
lected cooking zone comes on (see chapter
“Switching on the appliance”.)
– the sensor fields may be partially covered by a
damp cloth or by liquid.
… the residual heat indicator suddenly
fails to operate except for _ or h.
Check whether
– the “On/Off” switch was activated by mistake.
– the sensor fields may be partially covered by a
damp cloth, liquid or similar.
– the safety shut-down was activated.
23
Installation Instructions
Regulations, Standards,
Directives
1
Important! The new appliance may only be in-
stalled and connected by a registered spe-
cialist.
Please observe this instruction, otherwise the
warranty will not cover any damage that may
occur.
This appliance meets the following standards:
• EN 60 335-1 and EN 60 335-2-6
relating to the safety of electrical appliances for
household use and similar purposes and
Technical Data
• EN 60350, or DIN 44546 / 44547 / 44548
relating to the operating features of electric coo-
kers, hobs, ovens, and grills for household use.
• EN 55014-2
• EN 55014
• EN 61000-3-2
• EN 61000-3-3
Appliance dimensions
Width
Depth
Height
590 mm
520mm
55mm
relating to basic requirements for electro-magnetic
compatibility protection (EMC)
Worktop cut-out dimensions
5
This appliance complies with the following EU
Directives:
Width
Depth
Corner radius
560mm
490mm
R5
• 73/23/EWG dated 19.02.1973 (Low Voltage Direc-
tive)
• 89/336/EWG dated 03.05.1989 (EMC Directive in-
cluding Amending Directive 92/31/EWG).
Cooking rings
Position
Front left
Diameter
210mm
Power
2200W
(Power function
3000W)
Rear left
Rear right
Front right
180mm
145mm
180mm
1800W
1400W
1800W
(Power function
2300W)
Note: The quoted power consumption may vary ac-
cording to size and material of pans used.
Connection voltage
230 V ~ 50Hz
7,2kW
Maximum connected load power
24
1 Safety Instructions for
the Installer
• A device must be provided in the electrical installa-
tion which allows the appliance to be disconnected
from the mains at all poles with a contact opening
width of at least 3 mm
Suitable isolation devices include line protecting
cut-outs, fuses (screw type fuses are to be re-
moved from the holder), earth leakage trips and
contactors.
• In respect of fire protection, this appliance corre-
sponds to type Y (EN 60 335-2-6). Only this type of
appliance may be installed with a high cupboard or
wall on one side.
• Drawers may not be fitted underneath the hob.
• The installation must guarantee shock protection.
• The kitchen unit in which the appliance is fitted
must satisfy the stability requirements of
DIN 68930.
• For protection against moisture, all cut surfaces
are to be sealed with a suitable sealant.
• On tiled work surfaces, the joints in the area where
the hob sits must be completely filled with grout.
• On natural, artificial stone, or ceramic tops, the
snap action springs must be bonded in place with
a suitable artificial resin or mixed adhesive.
• Ensure that the seal is correctly seated against the
work surface without any gaps. Additional silicon
sealant must not be applied; this would make re-
moval more difficult when servicing.
• The hob must be pressed out from below when re-
moved.
• Clean the worktop around the cut-out area.
• Stick the single-sided adhesive sealing tape pro-
vided on the underside of the hob around the out-
side edge ensuring that it is not stretched. The two
ends of the tape should join in the middle of one
side. After trimming the tape (allow it to overlap by
2-3 mm), press the two ends together.
25
Electrical Connection
Before connecting, check that the nominal voltage of
the appliance, that is the voltage stated on the rating
plate, corresponds to the available supply voltage.
The rating plate is located on the lower casing of the
hob.
The heating element voltage is AC230V~. The appli-
ance also works perfectly on older networks with
AC220V~.
The hob is to be connected to the mains using a de-
vice that allows the appliance to be disconnected
from the mains at all poles with a contact opening
width of at least 3 mm, eg. automatic line protecting
cut-out,earth leakage tripsorfuse.
A type H05VV-F cable or one with a higher grade
must be used as the mains connecting cable.
The connection must be carried out as shown in the
diagram. The connecting links should be fitted ac-
cording to the appropriate connection diagram. The
earth lead is connected to terminal E. The earth lead
must be longer than leads carrying electric current.
The cable connections must be made in accord-
ance with regulations and the terminal screws
tightened securely.
Finally, the connecting cable is to be secured with
the mains cable cleat and the covering closed by
pressing firmly (lock into place).
Before switching on for the first time, any protective
foil or stickers must be removed from the glass ce-
ramic surface.
1
Once connected to the mains supply check
that all cooking zones are ready for use by
briefly switching each on in turn at the maxi-
mum setting.
26
Assembly
27
28
29
Guarantee Conditions
Standard guarantee conditions
European Guarantee
We, Zanussi, undertake that if within 24 months of
the date of the purchase this Zanussi appliance or
any part thereof is proved to be defective by reason
only of faulty workmanship or materials, we will, at
our option repair or replace the same FREE OF
CHARGE for labour, materials or carriage on condi-
tion that:
• The appliance has been correctly installed and
used only on the electricity supply stated on the
rating plate.
If you should move to another country within Europe
then your guarantee moves with you to your new
home subject to the following qualifications:
• The guarantee starts from the date you first pur-
chased your product.
• The guarantee is for the same period and to the
same extent for labour and parts as exists in the
new country of use for this brand or range of prod-
ucts.
• This guarantee relates to you and cannot be trans-
• The appliance has been used for normal domestic
purposes only, and in accordance with the manu-
facturer’s instructions.
ferred to another user.
• Your new home is within the European Community
(EC) or European Free Trade Area.
• The appliance has not been serviced, maintained,
repaired, taken apart or tampered with by any per-
son not authorised by us.
• All service work under this guarantee must be un-
dertaken by a Service Force Centre.
• Any appliance or defective part replaced shall be-
come the Company’s property.
• This guarantee is in addition to your statutory and
other legal rights.
Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visits may be available outside
these hours in which case a premium will be
charged.
• The product is installed and used in accordance
with our instructions and is only used domestically,
i.e. a normal household.
• The product is installed taking into account regula-
tions in your new country.
Before you move please contact your nearest Cus-
tomer Care centre, listed below, to give them details
of your new home. They will then ensure that the lo-
cal Service Organisation is aware of your move and
able to look after you and your appliances.
France
Germany Nürnberg
Italy
Sweden
UK
Senlis
+33 (0) 3 44 62 20 13
+49 (0) 800 234 7378
+39 (0) 800 11 7511
+46 (0) 20 78 77 50
+44 (0) 1753 219897
Pordernone
Stockholm
Slough
Exclusions
This guarantee does not cover:
• Damage or calls resulting from transportation, im-
proper use or neglect, the replacement of any light
bulbs or removable parts of glass or plastic.
• Costs incurred for calls to put right an appliance
which is improperly installed or calls to appliances
outside the United Kingdom.
• Appliances found to be in use within a commercial
environment, plus those which are subject to rental
agreements.
• Products of Zanussi manufacture which are not
marketed by Zanussi.
30
Service and Spare Parts
If you wish to purchase spare parts or require an en-
gineer, contact your local Service Force Centre by
telephoning:
08705 929 929
Your telephone call will be automatically routed to
the Service Force Centre covering your post code ar-
ea.
For the address of your local Service Force Centre
and further information about Service Force, please
visit the website at www.serviceforce.co.uk
When you contact the Service Centre they will need
the following information:
1.Your name & address, including post code.
2.Your telephone number
3.Clear and concise details of the fault.
4.The model and serial number of the appliance
(found on the rating plate).
5.The purchase date:
Please note that a valid purchase receipt or guaran-
tee documentation is required for in-guarantee serv-
ice calls.
Customer Care
For general enquiries concerning your Zanussi appli-
ance or for further information on Zanussi products
please contact our Customer Care Department by
letter or telephone at the address below or visit our
Customer Care Department
Electrolux
55-77 High Street
Slough
Berkshire, SL1 1DZ
Tel. 08705 727727(*)
(*) Calls may be recorded for training purposes.
Rating Plate
31
319 627 000-B-020603-03
Subject to change without notice
The Electrolux Group. The world´s No.1 choice.
The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products
(such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more
than 150 countries around the world.
|